Lenovo 6241 Installation And Service Manual Download Page 486

Page: 486 / 1990

Automatically notify support

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Make sure that the drive firmware is at the latest level.

4. Rerun the test after upgrading to the latest firmware level.

5. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

264-904-000 : Tape Test Failed

Tape Test Failed. Drive hardware error.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check the tape drive cabling for loose or broken connections or damage to the cable. Replace

the cable if damage is present.

2. Clean the tape drive using the appropriate cleaning media and install new media.

3. Run the test again.

4. Make sure that the drive firmware is at the latest level.

5. Rerun the test after upgrading to the latest firmware level.

6. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

264-905-000 : Tape Test Failed

Tape Test Failed. Software error: invalid request.

Recoverable

Severity

Error

Serviceable

Yes

472

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands