Lenovo 6241 Installation And Service Manual Download Page 487

Page: 487 / 1990

Automatically notify support

User Response

Complete the following steps:

1. If the system has stopped responding, turn off and restart the system.

2. Check the system firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

3. Run the test again.

4. If the system has stopped responding, turn off and restart the system.

5. Make sure that the drive firmware is at the latest level.

6. Run the test again.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

264-906-000 : Tape Test Failed

Tape Test Failed. Unrecognized error.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Make sure that the drive firmware is at the latest level.

4. Rerun the test after upgrading to the latest firmware level.

5. Make sure that the DSA Diagnostic code is at the latest level.

6. Run the test again.

7. Check the system firmware level and upgrade if necessary.

8. Run the test again.

9. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

•

264-907-000 : Tape Test Failed

An error was found in the block address somewhere.

Appendix B. DSA diagnostic test results

473

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands