Lenovo 6241 Installation And Service Manual Download | Manualshive

Page: 237 / 1990

background image

Attention:

Remove only one cover (on one side) at a time to protect the compute book

components on the other side of the compute book from being damaged.

Compute book
cover

Cover release/
touch points

Microprocessor
heatsink

Compute book

Step 6. Lift the cover off and set it aside.

Replacing the compute book cover

This information provides instructions on how to replace the compute book covers.

The compute book has a cover on the left side and a cover on the right side for access to the microprocessor
and DIMMs. Use the same procedure to remove both covers.

To access the microprocessor and DIMMs 1 through 12, remove the left cover.

To access DIMMs 13 through 24, remove the right cover.

To replace the compute book covers, complete the following steps:

Step 1. Align the cover on the rear of the compute book and slide it toward the front of the compute book

until it is secure.

.

Removing and replacing components

223

«
...
235
236
237
238
239
...
»

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6241

Brand: IBM Pages: 180

Brand: B&B Electronics Pages: 67

NovaScale R410B F2

Brand: Bull Pages: 38

Brand: Buffalo Pages: 2

SuperServer 6026TT-HIBQF

Brand: Supero Pages: 112

Brand: Intel Pages: 32

Brand: Advantech Pages: 96

FusionServer G8600 V7

Brand: xFusion Digital Technologies Pages: 112

419452u - Servers System X3250 M2 Xeon...

Brand: IBM Pages: 84

Brand: Discover Video Pages: 148

Brand: Eneo Pages: 94

Brand: Motorola Pages: 40

Brand: Motorola Pages: 90

TEW-MP2U - Wireless Multi-Function Print Server

Brand: TRENDnet Pages: 2

Brand: Black Box Pages: 93

m330 media server

Brand: Wadia Pages: 24

PROXYSERVER MTPSR1-120

Brand: Multitech Pages: 110

ProxyServer MTPSR3-200

Brand: Multitech Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands