Komatsu A31001 Operation & Maintenance Manual Download Page 325 | Manualshive

Page: 325 / 376

background image

ROUGH DIGGING MODE

Rough digging mode is used when the fine digging mode is not used. Bucket edge position against the design
data is displayed, and the light bar or sound supports the digging operation.
Tap the button (1) at bottom left of the working screen, and but-
ton pops up. Tap the button (1) and select Rough Digging
mode.
Rough Digging screen display can be changed by tapping the
button (2).

METHOD FOR SETTING ROUGH DIGGING SCREEN

(1) Light bar
Informs the bucket edge position against the design data with
color.
The range lit in green on the light bar is the tolerance of the
rough digging.
(2) Sound
Informs the bucket edge position against the design data with
sound.
For the light bar and sound, see “LIGHT BAR AND SOUND
SETTINGS (7-55)”.

(A) Sound is enabled
(B) Sound is disabled
Tap the button and ON/OFF of Sound can be switched.

2

1

AJD03165

EXECUTIONS

ROUGH DIGGING MODE

8-15

«
...
323
324
325
326
327
...
»

Summary of Contents for A31001

























































































































































































































































































































































































Reviews:

No comments

Related manuals for A31001

Brand: Komatsu Pages: 31

Brand: New Holland Pages: 41

Brand: Barreto Pages: 14

Brand: Camon Pages: 2

Brand: Hawk Pages: 27

Brand: Case Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands