Komatsu A31001 Operation & Maintenance Manual Download Page 229 | Manualshive

Page: 229 / 376

background image

Tap “Brightness Adjustment” button on “Display Options”
screen, the screen changes to Brightness Adjustment screen.

METHOD FOR ADJUSTING BRIGHTNESS ADJUSTMENT SCREEN

Adjust the brightness.

(1): Tap this button to decrease the brightness.
Tap this button and the number of green indicators (4) decreas-
es, and the screen becomes dark.
(2): Tap this button to increase the brightness.
Tap this button and the number of green indicators (4) increas-
es, and the screen becomes bright.
(3): With this button, you can return the brightness in Day and
Night to the default value.
For the default value in Day and Night, refer the position of
mark (5) on the green indicator (4).

SETTING

CONTROL BOX

7-113

«
...
227
228
229
230
231
...
»

Summary of Contents for A31001

























































































































































































































































































































































































Reviews:

No comments

Related manuals for A31001

Brand: jcb Pages: 51

Brand: jcb Pages: 51

Brand: Hyundai Pages: 41

Brand: Volvo Pages: 244

Brand: Kubota Pages: 41

Brand: Kubota Pages: 236

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands