Janich & Klass XINO S700 Series Translation Of The Original Operating Instructions Download

Page: 55 / 149

Rev. 1.01 Technical changes reserved.
© Janich & Klass Computertechnik GmbH, Wuppertal, 2015

page 6-19

XINO

S700

Operation

Chapter

6.3.1.3

Double feed detection

Actuating the double feed detection button opens the double feed detection 1 screen,

in which the double feed settings can be made.

Fig. 6-6

Double feed detection 1

Active

Yes

Switches the ultrasonic double feed detection on.

Switches the ultrasonic double feed detection off.

Acoustic

signal

Yes

Generates an acoustic signal when a double sheet is

detected.

No acoustic signal is generated when a double sheet

is detected.

Handling

Error

The scanner pauses when a double sheet is detected,

the sheet is stacked and an error screen is displayed.

The sheet has not been scanned and must be

scanned again.

Mark

The generated image is marked in the image header,

when a double sheet is detected. The scanning

process is not interrupted.

Double sheets can be handled via the scan software.

The document is scanned.

Inquire

The scanner pauses, when a double sheet is

detected, and an error screen with the image that

caused the error is displayed.

By means of the button

"accept double sheet and

continue" the images are transferred to the PC and

scanning continues.

Pressing either button

"discard double sheet and

continue"

"discard double sheet and pause" discards the

images. The sheet must be scanned again.

The faulty sheet is stopped in the outlet.

Summary of Contents for XINO S700 Series






















































































































































Search results

Summary of Contents for XINO S700 Series

Reviews:

Related manuals for XINO S700 Series

Brands by name

Popular brands

Janich & Klass XINO S700 Series, Translation Of The Original Operating Instructions

Search results

Summary of Contents for XINO S700 Series

Reviews:

Related manuals for XINO S700 Series

Brands by name

Popular brands