iPECS iPECS-LIK Feature Description & Operation Download Page 243

Page: 243 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

230

− To request delivery receipt of the message for future, press 5

Once the user has listened to a message that has been marked for receipt, the user that
marked the message will get a new message in their mailbox.

When they access this message a prompt will state: “message for XXXX (mailbox #) was
listened to on HH:MM

MM/DD”

This message is then treated a normal VM and all options apply.

Conditions

1. This option is only played to the mailbox owner if the mailbox COS allows it.

Programming

Related Features

Hardware

2.73.15 OUTGOING MAILBOX DESTINATION

Description

If a CO/IP incom

ing, Caller dials "0" when listening to a station’s VSF mailbox greeting the call

is routed according to the "Outgoing Mailbox Destination" as programmed for the station.

Operation

VSF outgoing mailbox destination call will be routed automatically.

Conditions

1. When a incoming call is routed to a unavailable destination as a outgoing mailbox

destination, Call will be routed to the Attendant.

Programming

STATION

1 STATION ATTRIBUTES (PGM114-BTN19)

Related Features

Hardware

2.73.16 Personal CCR / User Greeting DISA.

Description

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands