iPECS iPECS-LIK Feature Description & Operation Download Page 319 | Manualshive

Page: 319 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

306

4.16 ISDN SUPPLEMENTARY SERVICES

In many cases, the ISDN service provider offers enhanced services, to which a user may
subscribe. The iPECS system allows access to these ISDN “Supplementary Services”
implemented under the ETSI regime as described below.

4.16.1 ISDN Call Deflection

Description

When the ISDN Supplementary Service “Call Deflection” is supported, a user can forward
incoming calls on the ISDN line directly through the ISDN without the need to establish a
connection through the system.

When Call Deflection is used, the system sends a call-deflection request message with the
telephone number to receive the call to the ISDN. The ISDN then sends incoming calls to the
desired telephone number. In this case, the system does not set-up a CO line to CO line
(Unsupervised Conference) connection for the call.

Operation

iPECS Phone

To activate ISDN Call Deflection to an external number

1. Lift the handset or press the

[SPEAKER]

button to receive dial tone.

2. Press the

[FWD]

button.

3.

Dial Forward condition (“1”~“4”, “#”)

4. Press

[SPEED]

button and desired bin number.

5. Replace the handset, return to idle.

To deactivate ISDN Call Deflection

1. Press flashing

[FWD]

button, Call Forward will deactivate and the

[FWD]

button

LED is off.

Conditions

1. The ISDN must support the Call Deflection Supplementary Service as defined by

the ETS300-202/206/207 standard protocol.

2. ISDN lines that support Call Deflection must be assigned in the system database,

PGM 143, Btn 7.

Programming

CO/IP

1 ISDN-SS CD (PGM 143-Btn 7)

Related Features



ISDN Supplementary Services

«
...
317
318
319
320
321
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: Eaton Pages: 2

Brand: SVS Pages: 4

Brand: Dinstar Pages: 92

Brand: Zenitel Pages: 14

HD67F18-B2 Series

Brand: ADF Web Pages: 33

Brand: Zte Pages: 22

Brand: Nokia Pages: 5

Brand: Nokia Pages: 25

Brand: Nokia Pages: 56

Brand: Nokia Pages: 109

Brand: Nokia Pages: 129

Brand: Plugwise Pages: 28

Brand: BossPac Pages: 27

Brand: DatoHome Pages: 6

Brand: National Instruments Pages: 18

Brand: Cradlepoint Pages: 148

Mediola iQontrol Gateway

Brand: Kaiser Nienhaus Pages: 4

Brand: ZyXEL Communications Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands