iPECS iPECS-LIK Feature Description & Operation Download Page 192 | Manualshive

Page: 192 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

179

a TNET. Up to 30 VSF/VMIM could be used in MFIM1200.

7. You can set TNET enable ON/OFF for using TNET in local MFIM.

Programming

TNET

1 TNET Basic Attributes (PGM 330)

2 TNET Central MFIM Attributes (PGM 331)

3 TNET Local MFIM (PGM 332)

4 Fail-over PSTN Attributes

Related Features



Remote Device Zone Management

Hardware



Remote MFIM to support Local Survivability

2.70.2 Distributed Control Network

Description

In the Distributed Control Network, each iPECS system maintains control over the devices
registered to it. The networked systems communicate allowing other networked systems
access to resources over the network. In addition, other features and functions as detailed in
the following sections of this manual are available to users in a distributed network environment.
The iPECS permits remote access to various resources through registered gateway Modules
and terminals.

In addition, iPECS will request access to resources of remote systems. The user-dialed number
is analyzed and the call routed according to the Net numbering table. Should the main path fail
to respond, the iPECS routes the call employing the alternative Speed Dial route assigned.

iPECS supports two (2) standard protocols, QSIG over ISDN and H.450 over IP, for the basic
networking functions and the proprietary iPECS protocol for the advanced networking features.
QSIG employs ISDN PRI channels only with support for ESTI standards ETS 300-
237/238/256/257/260/261/361/362/363/364.

Operation

Operation of Distributed Networking is automatic when configured & defined

Conditions

1. To use the networking features, the software lock-key installation is required. Two

types of software lock-key relate to the networking protocols. One is for QSIG
based networking protocol, and another is for VOIP based networking protocol.
Each iPECS system has a unique software lock-key. To get the software lock-key,
contact the distributor of iPECS system.

2. Unified Dialing Plan (UDP): Each station can have a unique number up to 7 digits in

the networked systems, but it depends on their own numbering plan.

«
...
190
191
192
193
194
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

FieldServer FS-B35 Series

Brand: MSA Pages: 25

Brand: HMS Networks Pages: 20

Brand: ZyXEL Communications Pages: 12

AirLink PinPoint X

Brand: Sierra Wireless Pages: 62

Brand: RTA Pages: 71

Brand: Yeastar Technology Pages: 14

Brand: Advantech Pages: 74

Brand: NetComm Pages: 212

Brand: RTA Pages: 78

Brand: netvox Pages: 13

Brand: NETGEAR Pages: 7

SureCross DX80G9M6S0P0V4V4C

Brand: Banner Pages: 8

Brand: RFM Pages: 31

Brand: Juniper Pages: 26

Brand: NorthEast Monitoring Pages: 9

Brand: ADT Pulse Pages: 15

Brand: EnOcean Pages: 18

Brand: YX Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands