iPECS iPECS-LIK Feature Description & Operation Download Page 417 | Manualshive

Page: 417 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

404

Registration from the SIP Phone during the Registration Timer then system will
disconnect the SIP Phone automatically after Registration Timer expires.

− Manual : Re-Registration is not required for the SIP Phone

1. SIP Data / SIP Phone Attributes(211)

– TRANSPORT

− by default, UDP
− TLS : you need to set the Encryption Key. More technical information may be

required for you.

2. SIP Data / SIP Phone Attributes(211)

– SIP Phone Type

− Automatically determined by system

3. SIP Data / SIP Phone Attributes(211)

– Device NAT Usage

− AUTO : system determine automatically

Multi Line support for a SIP Phone

1. LIK allow multiple Extension for a SIP Phone that support Multi Line.

2. A SIP Phone will implement multiple register to system.

3. System will distinguish them by,

− 1

st

Extension : write it as a device with original MAC address

− from 2

nd

Extension : write it as a device with virtual MAC address

Conditions

1. You need to install Lock-Key for SIP Phones except Ericsson-LG LIP8002,

WIT400H, Yamaha ACT-50(PJP-50).

Programming

SIP DATA

1 SIP Attributes (210)

2 SIP Phone Attributes (211)

3 SIP Phone Provisioning (212)

Related Features

Hardware



MFIM1200:

Support up to 600 channels (SIP ext CO trunk) simultaneously



MFIM600:

Issue 0, 1, 2: Support up to 100 channels (SIP ext CO trunk) simultaneously

Issue 3 : Support up to 200 channels (SIP ext CO trunk) simultaneously



MFIM300:

Support up to 200 channels (SIP ext CO trunk) simultaneously



MFIM100:

Support up to 100 channels (SIP ext CO trunk) simultaneously



iPECS-50A/B, Micro:



Support SIP extension and CO trunk according to the maximum station and CO lines.

«
...
415
416
417
418
419
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: TIS Pages: 5

Brand: Actiontec Electronics Pages: 6

MESSAGING SECURITY GATEWAY -

Brand: F-SECURE Pages: 19

Brand: Echelon Pages: 3

Brand: SSS Siedle Pages: 2

BACnet Protocol

Brand: Bacharach Pages: 12

Brand: SiboTech Pages: 39

Brand: PREDICTWIND Pages: 16

Busch-free@home DG-M-1.16.11

Brand: Busch-Jaeger Pages: 35

Gateway 2070 Series

Brand: 2Wire Pages: 25

Brand: ZyXEL Communications Pages: 162

Brand: EuroTech Communication Pages: 42

Brand: Hybertone Pages: 73

VoIP FXS+PSTN Gateway

Brand: DBL Technology Pages: 44

Brand: 3Com Pages: 488

Brand: STIEBEL ELTRON Pages: 96

Brand: REPEATIT Pages: 17

EasyGateway EG400-HE

Brand: Aartesys Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands