iPECS iPECS-LIK Feature Description & Operation Download Page 198

Page: 198 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

185

Operation

To retrieve MWI message

1. Press the flashing

[MSG/CALLBK]

button and dial 2.

2. MWI contents (CLI number, date and time, the calling count from the same CLI) will

be shown on LCD.

700100
mm/dd hh/mm CNT:01

3. Press the

[

▲▼]

button. The previous or the next MWI is displayed.

To delete the current CLI Message and see the next one

Press “*” button.

2. Current MWI message is cleared with a confirmation tone and the next MWI

message is displayed.

To make a call back

1. Retrieve MWI with pressing the flashing

[MSG/CALLBK]

button and the

[

▲▼]

button.

2. Press

[SAVE]

button.

3. Then system makes a net call according to MWI data.

Conditions

1. MWI is applied to LCD panel installed station only.

2. When system makes a call back according to MWI data, the CO line is selected

within the network CO group.

Programming

STATION

1 Attribute (PGM114-BTN10 : CLI Message Wait)

SYSTEM

1 Networking Basic Attribute (PGM 320)

2 Networking CO Line Attribute (PGM 322)

3 Network Numbering Plan Table (PGM 324)

2.70.2.8 Net Call Forward

– Unconditional

Description

It is possible for a user to remotely forward to another station immediately over the network.

Engineering notice).

Currently, iPECS system supports both rerouting and join method by admin programming.

Operation

To activate Net Call Forward

1. Press the

[SPEAKER]

button and the

[FWD]

button.

Dial Net Call Forward code “1”, and dial the station number of another system. The

[FWD]

button will be flashing and a confirmation tone will be provided if allowed.

3. Dial the station number that is set Net Call Forward to a station of another node.

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands