manualshive.com logo in svg

iPECS iPECS-LIK, Feature Description & Operation

The iPECS iPECS-LIK Installer's Manual is a comprehensive guide that allows you to easily set up and customize your iPECS-LIK system. It provides step-by-step instructions and detailed illustrations, ensuring a hassle-free installation process. Download this manual for free from our website and empower yourself to maximize the full potential of your iPECS-LIK product.

Share
Download
background image

iPECS-LIK 
Feature Description & Operation Manual 

Issue 6.0d1 

 

 

150 

2.62 REGISTRATION & FRACTIONAL MODULE TABLES 

Description 

Normally, local iPECS devices can register with the system only when the “Registration Switch”, 
3rd Dip switch on the MFIM, is On. In this state, the system will allow any local iPECS device to 
register, providing a convenient “plug & play” initial installation. After initial installation, the 
Registration Switch is placed in the Off position, disabling registration of additional local device. 

To eliminate the potential for unintended device registration, particularly where multiple 
systems exist on the same LAN, the system can be programmed to allow local device 
registration employing MAC addresses. Using the defined MAC address registration, the 
system allows devices with matching MAC addresses to register regardless of the Registration 
Switch position. 

Three tables are provided to enter MAC addresses. The MAC Registration Table (PGM 102) 
allows entry of two MAC address ranges. Any device with a MAC address in either of the 
ranges will be permitted to register with the system. 

The second is the Fractional Module Table (PGM 235). This Table permits entry of five MAC 
addresses and the number of channels to be registered for each device. Entering the MAC 
address permits the device to register with the system regardless of the Registration Switch 
position. The number of channels available to the device is limited to the number of channels 
entered in the Table. This function is commonly used to limit the number of channels available 
over an E1/T1 or PRI ISDN circuit (Fractional T1 line). 

The third table allows entry of the MAC address of a remote phone or gateway Module as well 
as the Nation code and Zone. During registration, the system will compare the MAC address 
received from the remote device and, if matched, will permit registration of the device. Once the 
device is registered, the data for the device is placed in the appropriate locations and the data 
is removed from the Remote Phone & Gateway Registration Table. 

Operation 

Operation of registration is automatic based on the system database and Registration Switch 
position. 

Conditions 

Programming 

NUMBERING PLAN 

1  MAC Registration Table (PGM 102-Btn 11~14) 

TABLES 

1  Fractional Module Table (PGM 235) 

DEVICE LOGIN 

1  Remote Phone & CO Gateway Login, Web Admin 

only 

ZONE 

1  Zone Data, (PGM 436~441 &444, Web Admin only) 

Related Features 

Hardware 

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

ABB AWIN GW120 Quick Setup Manual preview
AWIN GW120
Brand: ABB Pages: 2
Eaton EMP Quick Start preview
EMP
Brand: Eaton Pages: 2
TCS Ubiquity QD2040b Product Manual preview
Ubiquity QD2040b
Brand: TCS Pages: 8
RTA 460MRSBMS Product User Manual preview
460MRSBMS
Brand: RTA Pages: 73
Kuhnt AS55 Series Service Manual preview
AS55 Series
Brand: Kuhnt Pages: 173
ProLinx 6201-WA-DFNT to DFNT Setup Manual preview
6201-WA-DFNT to DFNT
Brand: ProLinx Pages: 45
Geneko GWG User Manual preview
GWG
Brand: Geneko Pages: 158
Siemens SIMATIC IOT2020 Quick Install Manual preview
SIMATIC IOT2020
Brand: Siemens Pages: 2
Siemens SIMATIC IOT Gateway MQTT Installation Quick Manual preview
SIMATIC IOT Gateway MQTT
Brand: Siemens Pages: 2
Siemens MindConnect Nano Quick Start preview
MindConnect Nano
Brand: Siemens Pages: 2
Siemens Instabus/DALI Gateway N 141 Technical Product Information preview
Instabus/DALI Gateway N 141
Brand: Siemens Pages: 5
Siemens SIMATIC IOT2050 Product Information preview
SIMATIC IOT2050
Brand: Siemens Pages: 25
Siemens GAMMA 5WG1 143-1AB01 Operating And Mounting Instructions preview
GAMMA 5WG1 143-1AB01
Brand: Siemens Pages: 2
Siemens DCW1151 Installation Manual preview
DCW1151
Brand: Siemens Pages: 6
Siemens Gigaset SE567 Quick Start Manual preview
Gigaset SE567
Brand: Siemens Pages: 8
Siemens DESIGO RXC Manual preview
DESIGO RXC
Brand: Siemens Pages: 20
Siemens SIMATIC PN/M-Bus LINK Operating Instructions Manual preview
SIMATIC PN/M-Bus LINK
Brand: Siemens Pages: 62
Siemens HiPath HG 1500 Service Manual preview
HiPath HG 1500
Brand: Siemens Pages: 43

Brands by name

Popular brands

Load more brands