iPECS iPECS-LIK Feature Description & Operation Download Page 149 | Manualshive

Page: 149 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

136

2.55 MULTIPLE LANGUAGE SUPPORT

Description

With the VSF or VMIM, iPECS can support six (6) languages simultaneously. Prompts in the
desired languages are loaded into the VMIM/VSF memory along with the Language Selection
prompts. To assure the proper language is employed, the Language Selection prompts is
played when an incoming call is assigned to be answered by a DID, DISA, Auto Attd or station
hunt group announcement. The Language Selection prompts are played in multiple phrases,
one in each of the equipped languages, with a request for the caller to input a digit to select the
appropriate language. The system then employs the defined announcement (DID, DISA, etc.)
recorded for the selected language.

Operation

System

System automatically plays the Language Selection prompts and plays prompts in the
selected language.

To record a VMIM/VSF Multi Language Selection prompts

1. Press the

[PGM]

button.

2.

Dial “06”, the VMIM/VSF Record code.

3. Dial the VMIM/VSF device Sequence number.

4. Dial the VMIM/VSF Multi Language selection Announcement number, 72.

5. Dial the Language number, only required with multi-language support. The current

announcement is played followed by the “Press # to record” prompt.

6.

Dial “#”.

7. After the beep-tone, record message.

8. Press the

[SAVE]

button to stop recording and save the message.

Conditions

1. The Language Selection prompts must be recorded as announcement number 72.

2. Multi-language support is only available with the VMIM and VSF.

3. Separate announcements must be recorded by the Attendant for each language

supported.

Programming

SYSTEM

1 Multi-language (PGM 179)

Related Features



VMIM/VSF Integrated Auto Attd/Voice Mail



Direct Inward Dial (DID)



Station Groups



Announcements



Direct Inward System Access (DISA)

«
...
147
148
149
150
151
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

UNIGATE MB EtherCAT

Brand: DEUTSCHMANN AUTOMATION Pages: 60

Brand: VisionNet Pages: 102

Brand: TRBOnet Pages: 33

Brand: ProSoft Technology Pages: 154

Brand: ABB Pages: 11

Internet Security Gateway ZyWALL 100

Brand: ZyXEL Communications Pages: 708

ADSL2+ Ethernet/USB Gateway 660RU-Tx Series

Brand: ZyXEL Communications Pages: 286

Brand: Owon Pages: 12

Brand: IOGear Pages: 2

Brand: Burkert Pages: 13

Brand: ZyXEL Communications Pages: 20

Brand: Packet Power Pages: 2

Brand: Renu Electronics Pages: 98

Brand: RTA Pages: 66

Brand: Gainwise Pages: 10

Brand: 2N Telekomunikace Pages: 5

Mediatrix Model M

Brand: Mitel Pages: 40

Brand: Sagem Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands