iPECS iPECS-LIK Feature Description & Operation Download Page 234 | Manualshive

Page: 234 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

221

Flexible Number for “Company Directory Name” will be added to record the name of a person.
It can be dialed from an extension to record the name. And the recorded name will be played
for name search and during call transfer.

A new CCR digit in PGM 228 entry will be added. This value will be 13 and represent a
directory request. It can be assigned to any DTMF digit in a CCR menu. A new Flexible DID
Table in PGM 231 entry will be added. This value will be 14 and represent a directory request.

New system prompts will be added to the VMIB. The prompts will read as follows:



Press one to search by first name, Press two to search by last name.



Enter the first 3 characters of the person’s first name,



Enter the first 3 characters of the person’s last name



Transferring to [programmed name]



For [subscriber name]



press X (X = 1 ~ 9)



No match was found for your entry

Related Features



CCR

Hardware



VSF and/or VMIM

2.73.6 Record VM Greeting using CCR

Description

This feature provides an option to record a System (001-072) greeting in each VM Boards by
reaching CCR or Flexible DID Table.

Administrator can assign VM Greeting option at CCR menu or Flexible DID Table.

Operation

An outside caller reaches the CCR menu and presses the digit associated with recording a VM
Greeting prompt.

The system will prompt for a password “enter password”.

System main attendant telephone number, its password should be entered.

Once, the correct password is entered. System will check the installed VMIM board in the
system. And if there is only VMIM board, the system will prompt “enter system greeting
number”. But if there are two or more over installed VMIM boards in the system, the system will
prompt “enter slot number”.

(Please, remember installed VMIM slot number in iPECS system. You have to enter 3 digit for
slot number ex: 001, 010, … slot number of installed VMIM board)
If the correct slot number is dialed, the system will prompt “enter system greeting number”.

The user enters 001-072.

The system will prompt to record greeting

Once recorded, the system will allow re-record option.

«
...
232
233
234
235
236
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: CYP Pages: 12

Subnet16 BIS Z-GW-001-IND

Brand: Balluff Pages: 2

Brand: 3onedata Pages: 44

Brand: ZyXEL Communications Pages: 210

KNX-GSM Gateway

Brand: B+B Pages: 19

Brand: ZyXEL Communications Pages: 383

Brand: Telos Pages: 258

Brand: DatoHome Pages: 6

Brand: Technicolor Pages: 82

Brand: Technicolor Pages: 81

Brand: EnGenius Pages: 138

iCOMPEL EDS-S11

Brand: Black Box Pages: 2

Brand: Iseo Pages: 7

Brand: Bay Networks Pages: 64

multimax D4-IGW-1

Brand: KBR Pages: 20

Brand: Zenner Pages: 2

Brand: Rapid Controls Pages: 15

CheetahAccess AC-IG1004

Brand: Accton Technology Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands