iPECS iPECS-LIK Feature Description & Operation Download Page 406

Page: 406 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

393

5. During a Camp-On Broker Call, if the active party disconnects from the SLT, the

SLT user receives error tone. The SLT user may momentarily press the hook-
switch to retrieve the held party or go on-hook and receive recall.

6. If the SLT user presses the hook-switch twice in less than 2 seconds, a 3-way

conference is established.

7. If after a hook-

switch “Flash”, the user takes no action for the dial tone timer, the

SLT will receive error tone. If the SLT goes to an on-hook state, the SLT will
receive recall ring automatically.

Programming

Related Features



Message Wait/Call Back



Call Waiting/Camp-On



Exclusive Hold



Call Transfer



Conference

Hardware

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands