iPECS iPECS-LIK Feature Description & Operation Download Page 82 | Manualshive

Page: 82 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

69

Programming

Related Features



Multi-Party Voice Conference



Automatic Speaker Select



Hold Recall



Unsupervised Conference

Hardware



MCIM, Multi-party Conference gateway Module

2.23.2 Multi-Party Voice Conference

Description

The system allows multiple internal and external parties to be connected on a call, conference.

An unlimited number of 3-party conferences may be established using iPECS Phones. In
addition, each MCIM (Multi-party Conference Interface Module) up to 32 parties with the g.711
or g.729 codec and 24 with the g.723 codec may be connected in a single voice conference.

The MCIM will support any combination of parties and conferences to the maximum total
number of parties in conference. Multiple MCIMs, see chart below, are installed to support
multiple multi-party conferences with a maximum of 32 parties in any single conference.

iPECS-Micro

1 MCIM unit maximum

iPECS-50

2 MCIM units maximum

iPECS-300

4 MCIM units maximum

iPECS-600

8 MCIM units maximum

iPECS-1200

30 MCIM units maximum

Operation

iPECS Phone

To establish an ad-hoc conference

1. Establish first call.

2. Press the

[CONF]

button. The LED will light, the connected party is placed on

exclusive hold and the user receives dial tone.

3. Place second call.

4. When connected, press

[CONF]

, new call is placed on exclusive hold.

5. Repeat steps 3 and 4 above to add additional conference parties.

6. Press

[CONF]

button to establish conference.

To place a conference on hold

1. Press the

[HOLD]

button, the

[CONF]

button LED will flash.

To retrieve held conference

1. Press

[CONF]

button, all parties reconnected.

«
...
80
81
82
83
84
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Brand: rainforest Pages: 20

WILOW-IOT-GATEWAY-4G

Brand: BEANAIR Pages: 29

Brand: Rath Pages: 2

Brand: NeoGate Pages: 41

Brand: MatchX Pages: 20

Brand: ProSoft Technology Pages: 104

Brand: National Instruments Pages: 16

FieldGate SWG50

Brand: Endress+Hauser Pages: 48

Brand: Primus Pages: 2

Brand: Watchguard Pages: 30

TotalStorage NAS Gateway 500

Brand: IBM Pages: 471

Brand: GL-INET Pages: 48

Brand: Nateks Pages: 67

HomePortal 5012NV

Brand: 2Wire Pages: 18

Brand: IFM Electronic Pages: 22

Brand: ProSoft Technology Pages: 64

PLUS+1 Connect CS500

Brand: Danfoss Pages: 24

Brand: Sagem Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands