iPECS iPECS-LIK Feature Description & Operation Download Page 196

Page: 196 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

183

The busy station goes to Idle; the originator receives a call-back ring.

4. When the originator answers to the call-back ring, a new call will be activated to the

calling station.

Conditions

1. Stand-alone IP Phone that supports H.450 can activate the Call Completion feature.

2. A station can leave or have only one callback message, and a new request will be

left message wait indication message on busy station.

3. A voice message cannot be left even though the VMIM/VSF is installed in a local

system.

4. When the originator does not answer the call back ring within net timer, the call will

be cleared.

5. There are two modes: One is connection mode and the other is connectionless

mode. This can be selectable at PGM 320/BTN 8.

Programming

SYSTEM

1 Networking Basic Attribute (PGM 320)

2 Networking CO Line Attribute (PGM 322)

3 Network Numbering Plan Table (PGM 324)

2.70.2.5 Call Offer

Description

A busy user on one node is given notification that another call is waiting from another node. It is
similar to a Camp-On function.

Operation

To activate Call Offer

1. Dial a busy station number of another system. The caller hears a busy tone.

2. Press the

[CAMP ON]

button or “*” during hearing a busy tone.

3. The busy station receives an off-hook muted ring.

4. The calling station hears a ring-back tone instead of a busy-tone.

To answer the Call Offer

1. Press the flashing CO line button while receiving a muted ring.

Or,

1. The muted ring is changed to normal CO ring when you go on-hook state. Then you

can answer the offered call.

Conditions

1. Call Offer is only applied to a station that is in talk status.

2. During a conference or paging, call offer is not activated.

3. System does not support the path reservation mode of standard QSIG specification.

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands