iPECS iPECS-LIK Feature Description & Operation Download Page 402

Page: 402 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

389

6.19 SYSTEM CLOCK SET

Description

The System Attendant can set the system Time/Date.

Operation

System Attendant

To set the system clock

1. Press the

[PGM]

button.

Dial “041”, the Attendant Station Program code.

3. Dial six (6) digits for the Date (MM/DD/YY) or

[SAVE]

to skip the Date.

4. Dial four (4) digits for the Time (HH/MM) or

[SAVE]

to skip the Time setup.

5. Press the

[SAVE]

button, confirmation tone is heard and Attendant station returns to

idle status.

To set the system clock through ISDN message

1. Press the

[PGM]

button.

Dial “046”, the Attendant Station Program code.

Dial “1” to set DATE/TIME using ISDN message.

4. Press the

[SAVE]

button, confirmation tone is heard and Attendant station returns to

idle status.

Conditions

1. The time is entered as a 24-hour (military) clock, 24-hour mode.

2. If an NTP server is assigned, the system will check the time every ten (10) minutes.

If the system time is more than 10 seconds off of the NTP time, the system time is
reset. This will override the Attendant setting.

Programming

SYSTEM

1 Network Time/Date (PGM 161-Btn 12)

2 System Attendant (PGM 164-Btn 1)

3 System Time (PGM 178-Btn 1)

4 System Date (PGM 178-Btn 2)

5 DST Enable (PGM 178

– Btn 3)

6 DST Start & End Time (Web only)

7 NTP Active (PGM 195

– Btn 1)

8 NTP Sever address (Web only)

9 Std system time, local Time Zone (Web only)

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands