iPECS iPECS-LIK Feature Description & Operation Download Page 83 | Manualshive

Page: 83 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

70

SLT

To establish an ad-hoc a conference

1. Establish first call.

2. Momentarily press the hook-switch, the connected party is placed on exclusive hold

and the user receives dial tone.

3. Place second call.

4. When connected, repeat steps 2 and 3 above to add additional parties.

5. When completed adding parties, momentarily press hook-switch twice in 2 seconds,

all parties are connected.

Conditions

1. The

[CONF]

button remains illuminated at the initiators phone for the duration of the

conference.

2. There is no limit on the number of 3-way conferences the system will support with

iPECS Phones. With the MCIM, the system can support conferences of more than
3 parties. Each MCIM supports 32 conference channels with the g.711 or g.729
codec or 24 with the g.723 codec and can support multiple conferences with a total
maximum number of 32 or 24 users.

3. If all MCIM channels are busy when a request for a channel is received, the user will

receive error tone and the display will indicate that no Conference channels are
available.

4. If the system receives a disconnect signal and no internal parties remain in the

conference, the conference is terminated and all parties are disconnected. If an
internal party is still connected when a disconnect signal is received, the
connection to remaining parties is maintained.

5. The normal Hold Recall process is applied to a conference on hold using the

Unsupervised Conference recall Timer for recall timing.

6. If while setting up a conference, system error tone is received, the initiator must

press the

[CONF]

button (SLT must hook-flash) to regain Intercom dial tone.

7. A station that is busy, in DND or other non-idle state cannot be added to a

conference.

8. 8. The MCIM is also employed to support the Conference Room feature.

Programming

Related Features



Automatic Speaker Select



Hold Recall



Unsupervised Conference



Broker Call



Conference Room

Hardware



MCIM required to support voice conferences with more than 3 parties.

«
...
81
82
83
84
85
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Touchstone MG2402G

Brand: Arris Pages: 8

Brand: Gallagher Pages: 2

Voice Gateway H3C VG 10-10

Brand: H3C Pages: 31

SR6602-I AI Series

Brand: H3C Pages: 80

SR6602-I AI Series

Brand: H3C Pages: 33

SecPath M9000 Series

Brand: H3C Pages: 4

SecPath M9000 Series

Brand: H3C Pages: 15

MSR3610-I Series

Brand: H3C Pages: 5

SecPath M9000 Series

Brand: H3C Pages: 57

Brand: RTA Pages: 81

Brand: Pathway connectivity solutions Pages: 14

Brand: Pace Pages: 19

Brand: MediaAccess Pages: 68

Brand: NETGEAR Pages: 163

Brand: NETGEAR Pages: 25

Brand: NETGEAR Pages: 2

Brand: Hewlett Packard Enterprise Pages: 26

Brand: tiko Energy Solutions Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands