iPECS iPECS-LIK Feature Description & Operation Download Page 264 | Manualshive

Page: 264 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

251

2.86 FORCED DISCONNECT BUTTON (EMERGENCY

SUPERVISOR BUTTON)

Description

Each Digital station that have flexible button can make

[FORCED DISCONNECT]

button.

[PGM]

+

[Flex button]

+

[PGM]

+ [7#] +

[HOLD/SAVE]

.

In PGM 109

– Flex23, New Numbering Plan –

[Forced Seize Busy Stn/Co]

is added.

By using this button in DKT or By using this Numbering Plan Code in SLT or DKT, busy co-line
can be seized forcedly, busy station can be intruded forcedly.

Operation

To activate forced co-line disconnect feature:

1. Seize CO line.

2. The user hears busy tone

A. In digital phone, press

[Forced Disconnect]

button.

B. In digital phone, press

[TRANS/PGM]

button, and dial

[Forced Seize Busy

Stn/Co]

numbering plan code.

C. In SLT, do hook flash and dial

[Forced Seize Busy Stn/Co]

numbering plan

code.

3. Busy line goes to idle state forcedly and the user hears a dial tone.

To activate forced intrusion to a busy station feature:

1. Call to busy station.

2. The user hears busy tone

A. In digital phone, press

[Forced Disconnect]

button.

B. In digital phone, press

[TRANS/PGM]

button, and dial

[Forced Seize Busy

Stn/Co]

numbering plan code.

C. In SLT, do hook flash and dial

[Forced Seize Busy Stn/Co]

numbering plan

code.

3. Busy station connected with the user forcedly.

Conditions

1. SLT user also can use this feature by dialing numbering plan.

2. If the station was talking to other station or CO line, the call is disconnected when

the station receives forced Intrusion call.

3. The busy station is connected to forced intrusion caller only after short indication

with beep tone.

4. Forced Intrusion call is not possible to a station in DND state.

5. Forced Intrusion call is not possible to attendant.

Programming

Related Features Hardware

«
...
262
263
264
265
266
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

UNIGATE IC - Powerlink

Brand: DEUTSCHMANN AUTOMATION Pages: 50

Brand: iTAS Pages: 109

Adeo Control SGDD-C4-4

Brand: DALCNET Pages: 36

FieldServer ProtoNode

Brand: SMC Sierra Monitor Pages: 4

P-660HN-Fx series

Brand: ZyXEL Communications Pages: 12

LANLINK ZDIGLANLINK

Brand: DIGITAL YACHT Pages: 7

AirLink GX Series

Brand: Sierra Wireless Pages: 2

Brand: Pace Pages: 17

Brand: AVM Pages: 12

Brand: Innoband Pages: 87

Brand: Hewlett Packard Enterprise Pages: 26

Brand: IBM Pages: 2

Brand: IBM Pages: 20

Brand: Rockwell Automation Pages: 73

Brand: EuroTech Communication Pages: 42

Brand: Hybertone Pages: 73

Brand: Gigalink Pages: 46

EtherCAT SIG350

Brand: SICK Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands