11
MENU SCREEN
11-9
GPS items
GPS Select
(Default: Internal GPS)
MENU > GPS > GPS Set >
GPS Select
Select how to capture position data�
L
Data communication is disabled when you select
“External GPS�”
L
When “External GPS” is set, but if the external GPS
receiver is not connected, the internal GPS receiver
is temporarily turned ON when you use the Automatic
Position Reply function�
• OFF:
A GPS receiver is not used.
• Internal GPS: Position data of the internal GPS data
is used for the GPS functions�
• External GPS: Position data of an external GPS
receiver is used for the GPS
functions�
• Manual:
Manually enter the current Latitude,
Longitude, and Altitude in
Manual
Position
�
Power Save (Internal GPS)
(Default: Auto)
MENU > GPS > GPS Set >
Power Save (Internal
GPS)
Select whether or not to use the Power Save function
for the internal GPS receiver�
When this function is ON, and if the GPS receiver
does not receive signals from a satellite for 5 minutes,
the function turns OFF the GPS receiver for this set
period of time�
• OFF:
The GPS receiver is always turned
ON�
• 1, 2, 4, 8min: When the receiver cannot receive
signals from a satellite for 5 minutes,
the GPS receiver is turned OFF for the
selected period of time� (1, 2, 4, or 8
minutes)� After this period, the receiver
resumes receiving�
• Auto:
When the receiver cannot receive
signals from a satellite for 5 minutes,
the GPS receiver is turned OFF for 1
minute� After this period, the receiver
resumes receiving� The Power Save
interval time extends to 2, 4, and then
8 minutes when receiving no signals
for another 5 minutes, respectively�
Manual Position
(Default: LATITUDE: 0°00.00’N,
LONGITUDE: 0°00.00’W, ALTITUDE: ------ft)
MENU > GPS > GPS Set >
Manual Position
Manually enter the latitude, longitude, and Altitude of
your current position�
L
You can capture position data from the GPS receiver if
“Capture From GPS” is selected� (p� 5-3)
GPS Indicator
(Default: ON)
MENU > GPS > GPS Set >
GPS Indicator
Select whether or not to display the GPS icon (
)�
• OFF: The GPS icon is not displayed.
• ON: The GPS icon is displayed when valid position
data is received, and blinks when no position
data is received�
L
When
GPS Select
is set to “Manual,” the GPS
icon is not displayed�
Selected GPS
receiver
Not
connected
Connected/
Searching
Connected/
Received
Internal GPS
–
Blinks
Displayed
External GPS
Not
displayed
Blinks
Displayed
GPS Out (To DATA jack)
(Default: OFF)
MENU > GPS > GPS Set >
GPS Out (To DATA Jack)
Select whether or not position data of the internal
GPS receiver is output from the [DATA] jack�
• OFF: GPS position data is not output from the
[DATA] jack�
• ON:
GPS position data is output from the [DATA] jack�
TIP:
•
When
GPS Select
is set to “OFF,” “External GPS,”
or “Manual,” GPS position data is not output from
the [DATA] jack�
•
When you want to operate data communication
(p� 5-3) in the DV mode, set this item to “OFF�”
•
When this item is set to “ON,” you can output
GPS position data to another transceiver using its
[DATA] jack� In this case, you can use a handmade
stereo cable (Φ 2.5 mm).
q
q
'
q
TxD
q
'
RxD
w
RxD
w
'
TxD
w
w
'
GND
GND
Less than
Φ 6 mm (0.24 in)
Φ 2.5 mm
GND
ID-31A/E PLUS side
ID-9100 etc� side
NOTE:
The default settings shown below are for the USA transceiver version� The default settings may differ,
depending on your transceiver version� To return to your transceiver version’s default settings, see page 11-3�
