IC Realtime 1U POE NVR Series User Manual Download Page 50

Page: 50 / 291

Parameter

Description

DHCP

Enable the DHCP function. The IP address, subnet mask and
default gateway are not available for configuration once DHCP
is enabled.

● If DHCP is valid, the obtained information will display in the

IP Address

box,

Subnet Mask

box, and

Default Gateway

box. If not, all values show 0.0.0.0.

● If you want manually configure the IP information (static),

disable the DHCP function.

● If the PPPoE connection is successful, the IP address,

subnet mask, default gateway, and DHCP are not
available for configuration.

IP Address

Enter the IP address and configure the corresponding
subnet mask and default gateway.

IP address and default gateway must be in the same network
segment.

Subnet Mask

Default Gateway

DNS DHCP

Enabling DHCP function to get the DNS address from the router.

Preferred DNS

In the

Preferred DNS

box, enter the IP address of DNS.

Alternate DNS

In the

Alternate DNS

box, enter the IP address of the

alternate DNS.

Test

Click

Test

to test if the entered IP address and gateway are

interworking.

Step 4

Click

to go to NIC settings. Navigate to the

TCP/IP

interface.

Step 5

Set network parameters. See Table 4-6.

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Search results

Summary of Contents for 1U POE NVR Series

Reviews:

IC Realtime 1U POE NVR Series, User Manual, Page: 50 / 291

Search results

Summary of Contents for 1U POE NVR Series

Reviews: