manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 88 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 88

4.2.8 Checking PoE Status

This allows you to monitor PoE ports status or enable enhancement mode for each individual
PoE port.

Step 1

Select

Main Menu

>

Advanced> Camera Configuration > PoE

.

Figure 4-61

Step 2

(If Available) Set

Enhancement Mode

to

On

or

Off

.

When

On

is selected, the transmission distance of PoE port will be extended. This is

only for ePOE supported IP cameras. Extended transmission of cables longer than
network cable standards will have a reduced max transmission rate of 10mbps.

4.2.9 Remote Update

This function allows you to upgrade the connected IP camera firmware using a local file.
(IC Realtime cameras only)
You will need to have the firmware available on a USB to complete this step. Log into your
dealer portal and go to the product page to get the latest firmware. If unavaailable you can
contact support via email [email protected].

Step 1

Select

Main Menu

>

Advanced> Camera Configuration

>

Add/Remove Device

>

Upgrade

The

Update

interface will be displayed. See Figure 4-62.

77

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments