manualshive.com logo in svg

IC Realtime 1U POE NVR Series, User Manual, Page: 42 / 291

Share
Download
IC Realtime 1U POE NVR Series User Manual Download Page 42

4.1.3.3 Factory Reset Button (If Applicable)

Some units may have the reset button located on the motherboard to reset the Device to the
factory default settings. This function should only be done by qualified technicians.

The reset button is not available in some units.

On some units this function is disabled even if button is available.
Step 1

Disconnect the Device from the power source, and then remove the cover panel.
For details about removing the cover panel, see "3.4 HDD Installation".

Step 2

Find the reset button on the mainboard, and then connect the Device to the power
source again.

Step 3

Press and hold the reset button for 30 seconds. See Figure 4-15 for the location of
the reset button.

Figure 4-15

Step 4

The Device will reboot and all settings will be erased and set back to factory default.

4.1.4 Startup Wizard

After you have successfully initialized the device, the startup wizard will appear. Here you
can quickly configure your device. Click

Next

, to navigate to the

General

interface.

The startup wizard interface only displays after you first login the device and setup the admin
password. See Figure 4-16.

31

Summary of Contents for 1U POE NVR Series




































































































































































































































































































Reviews:

No comments