
8-82
ES User’s Guide
Hardkey/Softkey Reference
S
Softkey in the title and clock menu. Displays the clock on the
uppermost line of the title area when
is toggled
ON.
Access Keys:
Softkey in the title and clock menu. Displays the clock on the
uppermost line of the title area when
is toggled
ON.
Access Keys:
Softkey in the LAN menu. Displays the menu to setup the HP-IB
device address, HP-IB logical unit number, and HP-IB name for SICL
LAN control of the analyzer.
See The LAN Interface User’s Guide Supplement for more information.
Softkey in the trigger menu. Immediately stops the current sweep,
takes one complete sweep, and holds until retriggered by pressing
again, or
.
Access Keys:
Softkey in the format menu. A reflection measurement display format
that maps the complex reflection coefficient (rho) to the DUT's
impedance.
See
“Measuring Impedance using the Smith Chart” on page 3-73
more information.
Sets the characteristic impedance used by the analyzer in calculating
measured impedance with Smith chart markers and conversion
parameters. Characteristic impedance must be set correctly before
calibrating for a Smith chart measurement. Acceptable values are
1 ohm to 1000 ohms.
Access Keys:
Softkey in the SCPI sock. setup menu. Allows you to enter the port
number for a socket connection to the analyzer for SCPI socket
programming. The default port number is 5025.
See The LAN Interface User’s Guide Supplement for more information.
Show Clock
on Line 1
Title+Clk ON off
DISPLAY
More Display Title and Clock
Show Clock
on Line 2
Title+Clk ON off
DISPLAY
More Display Title and Clock
SICL LAN
Setup
Single
Single
Continuous
MENU
Trigger
Smith Chart
Smith Chart Z0
CAL
More Cal
Socket
Port No.
Summary of Contents for HP 8712ES
