manualshive.com logo in svg

Honeywell FBII CP-220A, Hookup And Installation Instructions

The Honeywell FBII CP-220A is a reliable and advanced security system, designed to safeguard your property. Ensure easy setup with our comprehensive Hookup And Installation Instructions manual, available for free download on our website. Discover the perfect balance of functionality and convenience with this top-of-the-line security solution.

Share
Download
background image

 (or RS-232) port of a modem or to another computer. 
When used with a modem, the CP-220A can send the data 
it processes via the modem to a remote location (similarly 
equipped with a modem), where it can be viewed, printed, 
and/or stored. 
NOTE: The use of a modem in this regard is beyond the 

scope of this manual. Inquiries about such 
applications should be made to FBI's Technical 
Support Department by calling (800) 645-7492. 

The cable used with such applications is also known as a 

serial

 cable and connects the CP-220A's DCE port to the 

corresponding port on the modem (or computer). The end of 
this cable at the CP-220A is a 25-pin "DB"-type connector; 
as with the DTE cable mentioned earlier, its other end will 
vary according to the type of serial port provided by the 
modem (or computer). Once again, contact FBI for help in 
cabling either of these ports to the corresponding 
equipment. 

 

AUX. 1 / AUX. 2

 

The AUX. 1 and AUX. 2 ports are used in conjunction with 
a REC-10 Line Card, which, when installed in the receiver, 
enables the CP-220A to receive and process signals from 

Derived Channel

 equipment in use in various locales 

throughout the country. 

Derived Channel

 technology 

provides telephone system supervision so that, along with 
alarms and system troubles, telephone service outages due 
to vandalism, accidents, or weather conditions can be 
reported to the proper Central Station. 
The REC-10 Line Card is designed to process such 
information using Versus Technologies' 

Base 10

 format.  

 

Telephone Lines

 

The CP-220A has the capacity to handle simultaneous 
incoming calls from up to 8 telephone lines. As stated on 
page 1-5, this requires the use of up to eight Line Cards, 
each of which corresponds to one of the eight telephone line 
connections on the CP-220A's rear panel. 
 
 

 

 

FIGURE 1-8 

 

CP-220A Central Station Receiver 

Section 1:  Getting Acquainted  Page 1-15 

Hook-Up and Installation Manual

 

The 8 pairs of TIP and RING terminals 

marked 1 through 8 accept up to eight 

telephone lines and correspond to the 

eight available Line Card slots within 

the CP-220A. Each incoming 

telephone line consists of two wires 

designated as the "TIP" and "RING," 

which reflect their polarity. The normal 

non-ringing, "on-hook" voltage 

produced by such pairs is typically 

between 48 and 55 volts DC, with the 

positive conductor designated as "TIP" 

and the negative conductor 

designated as "RING." This 

nomenclature dates back to the time 

when switchboard operators used 

phone plugs with "tip" and "ring" 

conductors to make manual telephone 

connections between calling parties. 

While such methods are no longer is 

use, the "tip" and "ring" designations 

have remained. 

Summary of Contents for FBII CP-220A































































































































































































Reviews:

No comments

Related manuals for FBII CP-220A

Majestic DAB 442BT Owner'S Manual preview
DAB 442BT
Brand: Majestic Pages: 13
Yamaha RX-V485 Owner'S Manual preview
RX-V485
Brand: Yamaha Pages: 155
Lowe Electronics HF-225 Technical Manual preview
HF-225
Brand: Lowe Electronics Pages: 50
Axxera AV714BH Installation & Owner'S Manual preview
AV714BH
Brand: Axxera Pages: 32
PCB Piezotronics JM353B18 Installation And Operating Manual preview
JM353B18
Brand: PCB Piezotronics Pages: 17
B&G Network V50 VHF Installation Instructions Manual preview
V50 VHF
Brand: B&G Network Pages: 22
Boss Audio Systems BV9370NV User Manual preview
BV9370NV
Brand: Boss Audio Systems Pages: 76
Intermatic RC613 Installation, Operation & Service Manual preview
RC613
Brand: Intermatic Pages: 2
Target Blu Eye 2 Installation Manual preview
Blu Eye 2
Brand: Target Pages: 10
Nav TV Tooki-Maserati Quick Start Manual preview
Tooki-Maserati
Brand: Nav TV Pages: 2
Hallicrafters SR-160 Technical Information preview
SR-160
Brand: Hallicrafters Pages: 28
COBHAM Messenger VETA User Manual preview
Messenger VETA
Brand: COBHAM Pages: 36
Alpine CDE-111R Owner'S Manual preview
CDE-111R
Brand: Alpine Pages: 37
World Vision T59M Manual preview
T59M
Brand: World Vision Pages: 10
Denon AVR-786 Service Manual preview
AVR-786
Brand: Denon Pages: 99
Eight HDR1 User Manual preview
HDR1
Brand: Eight Pages: 59
Delta SDR 510 U Manual preview
SDR 510 U
Brand: Delta Pages: 66
Galaxy Innovations Avatar2 User Manual preview
Avatar2
Brand: Galaxy Innovations Pages: 48

Brands by name

Popular brands

Load more brands