manualshive.com logo in svg

Hitachi H8S/2627, Hardware Manual

The Hitachi H8S/2627 Hardware Manual is an essential resource for users seeking a comprehensive guide for this product. Available for free download at manualshive.com, this comprehensive manual provides detailed instructions and insightful information, ensuring users can make the most of their experience with the Hitachi H8S/2627.

Share
Download
background image

Rev. 1.0, 09/02, page 326 of 568 

 

14.5 

Multiprocessor Communication Function 

Use of the multiprocessor communication function enables data transfer between a number of 
processors sharing communication lines by asynchronous serial communication using the 
multiprocessor format, in which a multiprocessor bit is added to the transfer data. When 
multiprocessor communication is performed, each receiving station is addressed by a unique ID 
code. The serial communication cycle consists of two component cycles; an ID transmission cycle 
that specifies the receiving station, and a data transmission cycle. The multiprocessor bit is used to 
differentiate between the ID transmission cycle and the data transmission cycle. If the 
multiprocessor bit is 1, the cycle is an ID transmission cycle; if the multiprocessor bit is 0, the 
cycle is a data transmission cycle. Figure 14.10 shows an example of inter-processor 
communication using the multiprocessor format. The transmitting station first sends the ID code 
of the receiving station with which it wants to perform serial communication as data with a 1 
multiprocessor bit added. It then sends transmit data as data with a 0 multiprocessor bit added. 
When data with a 1 multiprocessor bit is received, the receiving station compares that data with its 
own ID. The station whose ID matches then receives the data sent next. Stations whose IDs do not 
match continue to skip data until data with a 1 multiprocessor bit is again received. 

The SCI uses the MPIE bit in SCR to implement this function. When the MPIE bit is set to 1, 
transfer of receive data from RSR to RDR, error flag detection, and setting the SSR status flags, 
RDRF, FER, and ORER to 1, are inhibited until data with a 1 multiprocessor bit is received. On 
reception of a receive character with a 1 multiprocessor bit, the MPB bit in SSR is set to 1 and the 
MPIE bit is automatically cleared, thus normal reception is resumed. If the RIE bit in SCR is set to 
1 at this time, an RXI interrupt is generated. 

When the multiprocessor format is selected, the parity bit setting is rendered invalid. All other bit 
settings are the same as those in normal asynchronous mode. The clock used for multiprocessor 
communication is the same as that in normal asynchronous mode. 

Summary of Contents for H8S/2627






























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2627

GE MDS 4710M Setup Manual preview
MDS 4710M
Brand: GE Pages: 6
Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Patton electronics NetLink 2960 RAS Datasheet preview
NetLink 2960 RAS
Brand: Patton electronics Pages: 2
TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
Extron electronics PoleVault System A/V Source Inputs Specification Sheet preview
PoleVault System A/V Source Inputs
Brand: Extron electronics Pages: 4
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
ebm-papst R3G175-AF01-02 Operating Instructions Manual preview
R3G175-AF01-02
Brand: ebm-papst Pages: 11
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Brand: Datasat Pages: 24
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Brand: Ubiquiti Pages: 23
Logicube ZCLONE User Manual preview
ZCLONE
Brand: Logicube Pages: 56
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Brand: Icy Box Pages: 2
Cypress Semiconductor CY7C1410JV18 Specification Sheet preview
CY7C1410JV18
Brand: Cypress Semiconductor Pages: 26
NEC N8154-25 User Manual preview
N8154-25
Brand: NEC Pages: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Brand: Renesas Pages: 28

Brands by name

Popular brands

Load more brands