manualshive.com logo in svg

Hitachi H8S/2627, Hardware Manual

The Hitachi H8S/2627 Hardware Manual is an essential resource for users seeking a comprehensive guide for this product. Available for free download at manualshive.com, this comprehensive manual provides detailed instructions and insightful information, ensuring users can make the most of their experience with the Hitachi H8S/2627.

Share
Download
background image

Rev. 1.0, 09/02, page 117 of 568 

 

3.  Set the corresponding bit in DTCER to 1. 

4.  Set the SCI to the appropriate receive mode. Set the RIE bit in SCR to 1 to enable the 

reception complete (RXI) interrupt. Since the generation of a receive error during the SCI 
reception operation will disable subsequent reception, the CPU should be enabled to accept 
receive error interrupts. 

5.  Each time the reception of one byte of data has been completed on the SCI, the RDRF flag in 

SSR is set to 1, an RXI interrupt is generated, and the DTC is activated. The receive data is 
transferred from RDR to RAM by the DTC. DAR is incremented and CRA is decremented. 
The RDRF flag is automatically cleared to 0. 

6.  When CRA becomes 0 after the 128 data transfers have been completed, the RDRF flag is held 

at 1, the DTCE bit is cleared to 0, and an RXI interrupt request is sent to the CPU. The 
interrupt handling routine will perform wrap-up processing. 

 

8.7.2 Chain 

Transfer 

An example of DTC chain transfer is shown in which pulse output is performed using the PPG. 
Chain transfer can be used to perform pulse output data transfer and PPG output trigger cycle 
updating. Repeat mode transfer to the PPG’s NDR is performed in the first half of the chain 
transfer, and normal mode transfer to the TPU’s TGR in the second half. This is because clearing 
of the activation source and interrupt generation at the end of the specified number of transfers are 
restricted to the second half of the chain transfer (transfer when CHNE = 0). 

1.  Perform settings for transfer to the PPG’s NDR. Set MRA to incrementing source address 

(SM1 = 1, SM0 = 0), a fixed destination address (DM1 = DM0 = 0), repeat mode (MD1 = 0, 
MD0 = 1), and word size (Sz = 1). Set the source side as a repeat area (DTS = 1). Set MRB to 
chain mode (CHNE = 1, DISEL = 0). Set the data table start address in SAR, the NDRH 
address in DAR, and the data table size in CRAH and CRAL. CRB can be set to any value. 

2.  Perform settings for transfer to the TPU’s TGR. Set MRA to incrementing source address 

(SM1 = 1, SM0 = 0), a fixed destination address (DM1 = DM0 = 0), normal mode (MD1 = 
MD0 = 0), and word size (Sz = 1). Set the data table start address in SAR, the TGRA address 
in DAR, and the data table size in CRA. CRB can be set to any value. 

3.  Locate the TPU transfer register information consecutively after the NDR transfer register 

information. 

4.  Set the start address of the NDR transfer register information to the DTC vector address. 

5.  Set the bit corresponding to TGIA in DTCER to 1. 

6.  Set TGRA as an output compare register (output disabled) with TIOR, and enable the TGIA 

interrupt with TIER. 

7.  Set the initial output value in PODR, and the next output value in NDR. Set bits in DDR and 

NDER for which output is to be performed to 1. Using PCR, select the TPU compare match to 
be used as the output trigger. 

8.  Set the CST bit in TSTR to 1, and start the TCNT count operation. 

Summary of Contents for H8S/2627






























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2627

GE MDS 4710M Setup Manual preview
MDS 4710M
Brand: GE Pages: 6
LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Brand: Accusys Pages: 34
Analog Devices ADAU1961 Manual preview
ADAU1961
Brand: Analog Devices Pages: 76
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
FDI ELI70-CR Quick Start Manual preview
ELI70-CR
Brand: FDI Pages: 2
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Brand: Delta Electronics Pages: 1
Cameo WLG-1801 User Manual preview
WLG-1801
Brand: Cameo Pages: 23
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Brand: ZALMAN Pages: 16
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
Intel SRCSASPH16I - RAID Controller Hardware Manual preview
SRCSASPH16I - RAID Controller
Brand: Intel Pages: 28
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
Thecus N5200BR User Manual preview
N5200BR
Brand: Thecus Pages: 90
ST L6470H Manual preview
L6470H
Brand: ST Pages: 64
HYCON HY17S68 Series Hardware User Manual preview
HY17S68 Series
Brand: HYCON Pages: 13
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
Calix GigaSpire BLAST u6 Setup Manual preview
GigaSpire BLAST u6
Brand: Calix Pages: 9
Extron electronics Dual Window Multi-Graphic Processor MGP 462 Specifications preview
Dual Window Multi-Graphic Processor MGP 462
Brand: Extron electronics Pages: 2

Brands by name

Popular brands

Load more brands