manualshive.com logo in svg

Hitachi H8S/2627, Hardware Manual

The Hitachi H8S/2627 Hardware Manual is an essential resource for users seeking a comprehensive guide for this product. Available for free download at manualshive.com, this comprehensive manual provides detailed instructions and insightful information, ensuring users can make the most of their experience with the Hitachi H8S/2627.

Share
Download
background image

Rev. 1.0, 09/02, page 456 of 568 

 

19.6.1 Boot 

Mode 

Table 19.4 shows the boot mode operations from a reset end to a branch to the programming 
control program. 

1.  In boot mode, the flash memory programming control program must be prepared in the host 

beforehand. Prepare a programming control program in accordance with the description in 
section 19.8, Flash Memory Programming/Erasing. 

2.  SCI_2 should be set to asynchronous mode with the transfer format of 8-bit data, 1 stop bit, 

and no parity. 

3.  When the boot program is initiated, the chip measures the low-level period of asynchronous 

SCI communication data (H

′

00) transmitted continuously from the host. The chip then 

calculates the bit rate of transmission from the host, and adjusts the SCI_2 bit rate to match 
that of the host. The reset should end with the RxD pin high. The RxD and TxD pins should be 
pulled up on the board if necessary. After the reset is complete, it takes approximately 100 
states before the chip is ready to measure the low-level period. 

4.  When the bit rate matching is completed, the chip transmits 1-byte data H

′

00 to the host to 

indicate the end of bit rate adjustment. The host should confirm that this adjustment end 
indication (H

′

00) has been received normally, and transmit 1-byte data H

′

55 to the chip. If 

reception could not be performed normally, initiate boot mode again by a reset. Depending on 
the host’s transfer bit rate and system clock frequency of this LSI, there will be a discrepancy 
between the bit rates of the host and the chip. To operate the SCI properly, set the host’s 
transfer bit rate and system clock frequency of this LSI within the ranges listed in table 19.5. 

5.  In boot mode, a part of the on-chip RAM area is used by the boot program. The area 

H

′

FFE800 to H

′

FFEFBF is used to store the programming control program to be transferred 

from the host. The boot program area cannot be used until the execution is shifted to the 
programming control program. 

6.  Before branching to the programming control program, the chip terminates transfer operations 

by SCI_2 (by clearing the RE and TE bits in SCR to 0), however the adjusted bit rate value is 
retained in BRR. Therefore, the programming control program can still use it for transfer of 
write data or verify data with the host. At this time, the TxD pin is in the high level output 
state. The contents of the CPU general registers are undefined immediately after branching to 
the programming control program. These registers must be initialized at the beginning of the 
programming control program, since the stack pointer (SP), in particular, is used implicitly in 
subroutine calls, etc. 

7.  Boot mode can be cleared by a reset. End the reset by driving the reset pin low, waiting at least 

20 states, and then setting the mode (MD) pins. Boot mode is also cleared when a WDT 
overflow occurs. 

8.

 

Do not change the MD pin input level in boot mode. 

9.

 

All interrupts are disabled during programming or erasing of the flash memory. 

 

Summary of Contents for H8S/2627






























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2627

NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Brand: NEC Pages: 2
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Brand: TDK Pages: 2
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
SSV Embedded Systems eSOM/3517 Hardware Reference Manual preview
eSOM/3517
Brand: SSV Embedded Systems Pages: 17
LUX LUMEN 10230 Manual preview
10230
Brand: LUX LUMEN Pages: 41
National Instruments PCI-6601 User Manual preview
PCI-6601
Brand: National Instruments Pages: 52
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Brand: Multiplex Pages: 10
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Brand: Antec Pages: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Brand: Knowles Pages: 14
ENERMAX ELC-LMT120-RGB User Manual preview
ELC-LMT120-RGB
Brand: ENERMAX Pages: 33
UMAX Technologies SuperMac E100 User Manual preview
SuperMac E100
Brand: UMAX Technologies Pages: 27
Uctronics U6187 Assembly Manual preview
U6187
Brand: Uctronics Pages: 12
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
VANTAS DPA-S50 Owner'S Manual preview
DPA-S50
Brand: VANTAS Pages: 30
Actisense W2K-1 Install And User Manual preview
W2K-1
Brand: Actisense Pages: 14
MTL 9468-ET Instruction Manual preview
9468-ET
Brand: MTL Pages: 12

Brands by name

Popular brands

Load more brands