manualshive.com logo in svg

Hitachi H8S/2627, Hardware Manual

The Hitachi H8S/2627 Hardware Manual is an essential resource for users seeking a comprehensive guide for this product. Available for free download at manualshive.com, this comprehensive manual provides detailed instructions and insightful information, ensuring users can make the most of their experience with the Hitachi H8S/2627.

Share
Download
background image

Rev. 1.0, 09/02, page 72 of 568 

 

5.4.2 Internal 

Interrupts 

The sources for internal interrupts from on-chip peripheral modules have the following features: 

•

 

For each on-chip peripheral module there are flags that indicate the interrupt request status, 
and enable bits that select enabling or disabling of these interrupts. If both of these are set to 1 
for a particular interrupt source, an interrupt request is issued to the interrupt controller. 

•

 

The interrupt priority level can be set by means of IPR. 

•

 

The DTC can be activated by a TPU, SCI, or other interrupt request. 

•

 

When the DTC is activated by an interrupt request, it is not affected by the interrupt control 
mode or CPU interrupt mask bit. 

 

5.5 

Interrupt Exception Handling Vector Table 

Table 5.2 shows interrupt exception handling sources, vector addresses, and interrupt priorities.  

For default priorities, the lower the vector number, the higher the priority. Priorities among 
modules can be set by means of IPR. Modules set at the same priority will conform to their default 
priorities. Priorities within a module are fixed. 

Summary of Contents for H8S/2627






























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2627

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
hawa HAWA-Frontside 60/B Planning And Installation Instructions preview
HAWA-Frontside 60/B
Brand: hawa Pages: 28
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
Measurement Computing PC-CARD DAS16 User Manual preview
PC-CARD DAS16
Brand: Measurement Computing Pages: 27
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
Giacomini KPM36Y002 Manual preview
KPM36Y002
Brand: Giacomini Pages: 2
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48
Supero AOC-1UIPMI-B User Manual preview
AOC-1UIPMI-B
Brand: Supero Pages: 53
3Com FEM656C Quick Start Manual preview
FEM656C
Brand: 3Com Pages: 53
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
ADTRAN 1200864L1 Quick Start Manual preview
1200864L1
Brand: ADTRAN Pages: 2
Aim ACE1553-3U-4 Hardware Manual preview
ACE1553-3U-4
Brand: Aim Pages: 35
c SwiftreaderX Installation Manual preview
SwiftreaderX
Brand: c Pages: 32
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
NetApp NS224 Instructions Manual preview
NS224
Brand: NetApp Pages: 28
Epson IMU G Series User Manual preview
IMU G Series
Brand: Epson Pages: 19
Epson PP-100 III Setup Manual preview
PP-100 III
Brand: Epson Pages: 2

Brands by name

Popular brands

Load more brands