Higen FDA7000 Series Operation Manual Download Page 150

Page: 150 / 214

5. Servo operating

4-19

◆

If you set the system response to high, it increases the servo system gain to increase the

response. But if the set value is too high, it can cause noise and vibration in the motor. In this

case, appropriately lower the set value.

4.4.2. Auto-tuning setting sequence

Manually adjust system response

(P02-18)

Test operation with basic setting

Repeated acceleration/deceleration

operation (*) (500rmp or above)

Operation

OK ?

Does load inertia

change ?

Turn ON on-line tuning mode

(P02-17)

Yes

Operation

OK ?

Yes

Turn OFF autotuning mode

Manually adjust load inertia (P02-19)

END

Save tuning result

(P02-19)

Yes

START

♥ Auto-tuning is set by system response setting (P02-18) manual part, by position loop gain,

speed control loop gain, SC TC and torque command filter and the system inertia ratio

(P02-19) is set by the Auto-tuning mode (P02-17).

Summary of Contents for FDA7000 Series























































































































































































































Search results

Summary of Contents for FDA7000 Series

Reviews:

Related manuals for FDA7000 Series

Brands by name

Popular brands

Higen FDA7000 Series, Operation Manual

Search results

Summary of Contents for FDA7000 Series

Reviews:

Related manuals for FDA7000 Series

Brands by name

Popular brands