GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 58 / 346

Cable NH10GE K2 Media Server

As directed by the system diagram for your K2 SAN, cable the NH10GE K2 Media Server or Servers
for your K2 SAN using the instructions in this section

K2-SVR-NH10GE online/production Dell R620

These cabling instructions apply to the following:

•

Dell R620 PowerEdge Server NH10GE on an online or production K2 SAN.

If you have more than one NH1 server, balance servers between controller 0 and controller 1.

K2-SVR-NH10GE basic nearline Dell R620

These cabling instructions apply to the following:

•

Dell R620 PowerEdge Server NH10GE on a basic nearline K2 SAN.

K2-SVR-NH10GE redundant nearline Dell R620

These cabling instructions apply to the following:

•

Dell R620 PowerEdge Server NH10GE on a nearline K2 SAN.

K2 SAN Installation and Service Manual

2014 01 27

Cabling K2 SAN devices

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands