GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 208 / 346

5. Enter the control network IP address and other network settings.

6. For SNMP Configuration, enter the IP address of the SNMP manager PC.

You can also enter IP addresses for other SNMP managers to which you want to send SNMP
trap messages.

Refer to related topics about Grass Valley recommended deployment and monitoring solutions
in "K2 Release Notes".

7. For the RAID chassis with two controllers, in the Controller Slot Number field enter

and then

press

Enter

The settings from controller 1 are loaded into the Controller Network Settings dialog box and
are available for you to modify.

8. Repeat the previous steps to configure controller 1.

9. Click

to save settings and close.

10. In Storage Utility click

View | Refresh

Next, bind disk modules.

Binding disk modules - Nearline K2 SAN

Prerequisites for the K2 RAID chassis are as follows:

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

•

Power on

Prerequisites for the optional K2 RAID Expansion chassis (if present) are as follows:

•

Fibre channel cable(s) connected

•

Power on

NOTE: Binding destroys all user data on the disks.

1. If you have not already done so, launch Storage Utility from the K2Config application.

2. As prompted, wait while Storage Utility gathers system information, then Storage Utility opens.

208

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands