GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 184 / 346

Configure New K2 System page 3 - Nearline K2 SAN

1. Review the information on this page and verify that you have correctly defined your K2 SAN.

For a redundant nearline K2 SAN you should have the following:

•

Two Gigabit Ethernet switches

•

Two K2 Media Servers

2. Click

Finish

The Define New K2 Storage System wizard closes.

Your storage system appears in the tree view of the K2Config application.

Next, configure the server.

Configuring NH server - Part 1

1. In the K2Config application tree view, select

[K2Server1]

For the basic nearline K2 SAN, this is the only NH server.

2. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

184

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands