GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 168 / 346

background image

Configure Network Configuration page - Redundant K2 SAN server A and server B

This page displays the control network Ethernet port, and allows you to configure the FTP/Streaming
network Ethernet port.

NOTE: This page does not configure the iSCSI interface (media network) ports.

1. Verify that the top port is configured correctly.

The top port is the port over which the K2Config application is communicating. If correctly
configured, it is already assigned the control network IP address, as displayed on this page.

2. If the server has the role of FTP server, verify that the other port is configured correctly. If not

configured correctly, do the following:

a) Select the other port and click

Modify

.

A network configuration dialog box opens.

b) Enter the FTP/Streaming IP address and the subnet mask and click

Apply

.

For systems with an optional NH (FTP) server, the server you are now configuring does not take
the role of FTP server, so configuring the second port here for the FTP/streaming network is not
required.

3. Click

Next

.

The File System Server Configuration page opens.

168

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

«
...
166
167
168
169
170
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

18-51000 Series

Brand: Salsbury Industries Pages: 5

Brand: QNAP Pages: 63

Brand: Medion Pages: 2

SG-XPCIESAS-R-INT-Z

Brand: Oracle Pages: 148

Brand: Apricorn Pages: 36

Brand: Galvo Shed Pages: 8

Brand: Metro DataVac Pages: 16

Brand: OYEN DIGITAL Pages: 1

Brand: morse Pages: 4

Brand: Hitachi Pages: 1

Brand: Seagate Pages: 2

TS-269L TurboNAS

Brand: QNAP Pages: 6

Brand: SIRCHIE Pages: 8

Brand: Powerline Pages: 2

Superstor GL-119

Brand: HTP Pages: 12

Brand: Heartland Pages: 71

Brand: Datex Pages: 15

TotalStorage DS5100

Brand: IBM Pages: 296

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands