GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 118 / 346

Manage Embedded Security Update mode

1. From the Windows desktop, click

Start | All Programs | Grass Valley | Embedded Security Manager

Embedded Security Manager opens.

Interpret Current Status as follows:

•

Enabled

: Embedded Security is enabled but is not in Update mode.

•

Update

: Embedded Security is enabled and is in Update mode, ready for software installation.

2. Manage the Update mode as follows:

•

If Embedded Security is not in Update mode, click

Enter

to put it in Update mode.

•

If Embedded Security is already in Update mode, click

Leave

to take it out of Update mode.

A restart is not required after you change the Update mode.

118

K2 SAN Installation and Service Manual

2014 01 27

Managing K2 Software

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands