manualshive.com logo in svg

GRASS VALLEY K2 SAN, Installation And Service Manual

The GRASS VALLEY K2 SAN Installation And Service Manual is a comprehensive guide that provides step-by-step instructions on setting up and servicing the K2 SAN system. This essential manual is available for free download on our website, allowing users to access the information they need conveniently and effortlessly.

Share
Download
background image

Configure File System Server Configuration page - NH server

This page checks on the file system server role. The server also functions as a file system client,
which is also checked from this page.

1. Do not select

Reserved Bandwidth

unless instructed to do so by Grass Valley. This system is

usually not configured for RVIO.

2. Click

Launch Storage Manager

.

Storage Utility opens.

3. Leave the Configure K2 Server wizard open while you use Storage Utility.

When you are done with Storage Utility, you continue with the wizard.

Next, use Storage Utility to configure the RAID storage and file system.

Configuring RAID

Use Storage Utility to complete the configuration of the K2 RAID storage devices, as explained in
the following topics.

Configuring RAID network and SNMP settings - Basic

Prerequisites for the K2 RAID chassis are as follows:

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

•

Power on

Prerequisites for the optional K2 RAID Expansion chassis (if present) are as follows:

•

Fibre channel cable(s) connected

188

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Quantum LTO 3 Reference Manual preview
LTO 3
Brand: Quantum Pages: 78
Xigmatek Lighter 60 GB User Manual preview
Lighter 60 GB
Brand: Xigmatek Pages: 2
Hama 104389 Operating Instructions Manual preview
104389
Brand: Hama Pages: 8
Y-E Data YD-380 Maintenance Manual preview
YD-380
Brand: Y-E Data Pages: 48
Western Digital SiliconEdge Blue Series Brochure & Specs preview
SiliconEdge Blue Series
Brand: Western Digital Pages: 2
Kikusui 3P05-PCR-LE Setup Manual preview
3P05-PCR-LE
Brand: Kikusui Pages: 6
QNAP TVS- 72XU Series User Manual preview
TVS- 72XU Series
Brand: QNAP Pages: 56
Sony MSX-M1GN Operating Instructions preview
MSX-M1GN
Brand: Sony Pages: 2
Sony MSX-1G Operating Instructions preview
MSX-1G
Brand: Sony Pages: 2
Sony MSH-128S2 Operating Instructions preview
MSH-128S2
Brand: Sony Pages: 2
Sony MSMT16G Operating Instructions preview
MSMT16G
Brand: Sony Pages: 2
Sony MSHX16G - Memory Stick PRO-HG Duo HX 16 GB Operating Instructions preview
MSHX16G - Memory Stick PRO-HG Duo HX 16 GB
Brand: Sony Pages: 2
Sony MSG-M64A Operating Instructions preview
MSG-M64A
Brand: Sony Pages: 4
Sony MSAC-US1 Operating Manual preview
MSAC-US1
Brand: Sony Pages: 28
ENHANCE TECHNOLOGY E800MS Quick Start Manual preview
E800MS
Brand: ENHANCE TECHNOLOGY Pages: 6
Duratuf KIWI MK3B Assembly Instructions Manual preview
MK3B
Brand: Duratuf KIWI Pages: 18
ASUSTOR AS63 Series Memory Installation Manual preview
AS63 Series
Brand: ASUSTOR Pages: 9
Cavalry CAXT Series User Manual preview
CAXT Series
Brand: Cavalry Pages: 16

Brands by name

Popular brands

Load more brands