GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 326 / 346

background image

iSCSI extended (redundant FSMs)

RAID Storage

GigE Fabric

K2 SAN-attached client systems

FSM/Bridge

K2 Media Servers

FTP/Bridge

K2 Media Servers

Fibre Channel Fabric

Control Point PC

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

POWER

SERVICE

K2

RAID STORAGE

!!

!

K2

MEDIA SERVER

!

K2

MEDIA SERVER

!

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

K2

MEDIA SERVER

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

iSCSI

Key to illustrated cable paths:

Gigabit Ethernet carrying real-time media

Fibre Channel carrying real-time media

Gigabit Ethernet carrying traffic that is not

real-time media

A black/gray pair denotes redundant cables

This system differs from the Level 3R system as follows:

•

A Fibre Channel switch fabric, comprised of one or more Fibre Channel switches, is interposed
between K2 Media Servers and the RAID Storage devices. This allows more RAID Storage
devices to be connected, which provides higher bandwidth and more storage space.

•

Additional FTP/Bridge K2 Media Servers are added, providing additional iSCSI bridges to
support more clients and higher bandwidth clients.

Guidelines for this system are as follows:

•

The Fibre Channel switch fabric must be zoned.

Related Topics

Fibre Channel switch zoning

on page 330

326

K2 SAN Installation and Service Manual

2014 01 27

Custom K2 SAN systems

«
...
324
325
326
327
328
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Brand: Gearwrench Pages: 9

Brand: Premio Pages: 3

Brand: ATI Technologies Pages: 24

Brand: Impediment Pages: 256

Brand: Olympus Pages: 4

Brand: Alphacool Pages: 2

Catalina KC-103

Brand: SPAREHAND Pages: 2

Tech Tub2 FTT600

Brand: Copernicus Pages: 13

Brand: HOGYME Pages: 31

Brand: Sanyo Pages: 8

Brand: Sanyo Pages: 26

Brand: Siemens Pages: 2

Brand: Siemens Pages: 40

Gigaset USB Stick 108

Brand: Siemens Pages: 58

SIMODRIVE 611-D

Brand: Siemens Pages: 1154

Brand: Ferm Pages: 4

Brand: Duratuf KIWI Pages: 18

Brand: Sunpal Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands