GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 153 / 346

background image

2. Click

Launch Storage Manager

.

Storage Utility opens.

3. Leave the Configure K2 Server wizard open while you use Storage Utility.

When you are done with Storage Utility, you continue with the wizard.

Next, use Storage Utility to configure the RAID storage and file system.

Configuring RAID

Use Storage Utility to complete the configuration of the K2 RAID storage devices, as explained in
the following topics.

Configuring RAID network and SNMP settings

Prerequisites for the K2 RAID chassis are as follows:

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

•

Power on

Prerequisites for the optional K2 RAID Expansion chassis (if present) are as follows:

•

Fibre channel cable(s) connected

•

Power on

Use the Storage Utility to configure the following settings for the K2 RAID controller:

•

IP address

•

Subnet mask

•

Gateway Address

•

SNMP trap destinations

For K2 RAID, network and SNMP settings are set and stored on the RAID controller module. For
the RAID chassis with two controllers, each controller has its own network settings and the RAID
chassis exists as two entities on the control network.

The RAID storage device is configured by default for the SNMP community name “public”. If your
site’s policies require using a different SNMP community name, contact your Grass Valley
representative.

1. Launch Storage Utility from the K2Config application.

2. As prompted, wait while Storage Utility gathers system information, then Storage Utility opens.

2014 01 27

K2 SAN Installation and Service Manual

153

Configuring and licensing the K2 SAN

«
...
151
152
153
154
155
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Brand: IBM Pages: 18

Brand: IBM Pages: 180

Brand: Yamaha Pages: 3

Spinpiont HD320KJ

Brand: Samsung Pages: 1

System Storage TS2900

Brand: IBM Pages: 130

Brand: IBM Pages: 2

LIBRARIES D2175

Brand: Plasmon Pages: 90

Brand: Apricorn Pages: 4

Brand: Hama Pages: 8

Pietas FlashPen

Brand: Hama Pages: 8

Brand: HermanMiller Pages: 5

Brand: Würth Pages: 196

Brand: SanDisk Pages: 18

E-Series 3040 40U

Brand: NetApp Pages: 32

Brand: MAXDATA Pages: 6

Brand: Maxtor Pages: 2

Brand: Maxtor Pages: 82

Maxtor OneTouch USB

Brand: Maxtor Pages: 268

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands