GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 148 / 346

Configure New K2 System page 2 - Redundant K2 SAN

1. Move the following into the Number of devices box:

•

Two K2 Media Servers

•

Two Ethernet switches

•

K2 clients as appropriate for your system.

•

(Optional) One or more K2 Media Servers to represent each NH K2 Media Server on your
system.

•

(Optional) Other devices as appropriate for your system.

2. Click

Next

Page 3 opens.

148

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands