GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 217 / 346

background image

Configure Network Configuration page - NH server

This page displays the control network Ethernet port, and allows you to configure the FTP/Streaming
network Ethernet port.

1. Verify that the top port is configured correctly.

The top port is the port over which the K2Config application is communicating. If correctly
configured, it is already assigned the control network IP address, as displayed on this page.

2. Verify that the FTP/Streaming port is configured correctly. If not configured correctly, do the

following:

a) Select the other port and click

Modify

.

A network configuration dialog box opens.

b) Enter the FTP/Streaming IP address and the subnet mask and click

Apply

.

3. Click

Next

.

The File System Server Configuration page opens.

2014 01 27

K2 SAN Installation and Service Manual

217

Configuring and licensing the K2 SAN

«
...
215
216
217
218
219
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Brand: IBM Pages: 62

Brand: U.S. General Pages: 6

Brand: Dell EMC Pages: 70

Travelstar 14GS

Brand: IBM Pages: 2

Brand: Maxtor Pages: 73

Brand: Thecus Pages: 130

SmartStore SM2015

Brand: Riverlea Pages: 16

TotalStorage Network Attached Storage 300G

Brand: IBM Pages: 86

TUSCANY TERRACE 100.1P

Brand: garofalo Pages: 16

Brand: LevelOne Pages: 85

Brand: Cavalry Pages: 16

Brand: Cavalry Pages: 16

CADA-C32A Series

Brand: Cavalry Pages: 18

Brand: Hitachi Pages: 58

Brand: Hitachi Pages: 192

Brand: Tuff Nano Pages: 17

Brand: Symantec Pages: 2

Brand: Samsung Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands