GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 173 / 346

background image

Check the V: drive

Prerequisites:

•

The K2 Media Server is configured

•

The restart of the K2 Media Server after it is configured is complete

This task is required for NAS server functionality.

1. Verify that the K2 Media Server has restarted by opening the MS-DOS command prompt and

use the “ping” command.

2. In the K2Config application tree view, under the K2 Media Server select the File System Server

node.

The File System Server Configuration page appears.

3. Click

Check

and verify that the V: drive is shared.

Proceed as follows:

•

If you have NH servers, configure them next.

•

If you do not have NH servers, configure K2 clients and/or other iSCSI clients on the K2 SAN
next.

Configuring optional NH servers

If you have one or more optional NH K2 Media Servers, you next configure those servers. This
section applies to both NH1 (1 Gig FTP) servers and NH10GE (10 Gig FTP) servers.

NOTE: Multiple NH servers on a K2 SAN must be of the same type, either all NH1 or all NH10GE.

1. In the K2Config application tree view, select the K2 Media Server you are configuring.

2. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

2014 01 27

K2 SAN Installation and Service Manual

173

Configuring and licensing the K2 SAN

«
...
171
172
173
174
175
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

A16F-R2431 Galaxy Raid

Brand: Rorke Data Pages: 110

Brand: Seagate Pages: 24

Brand: LaCie Pages: 2

Brand: Seagate Pages: 44

Brand: SanDisk Pages: 2

Brand: G&T SALES Pages: 2

Brand: AIC Pages: 101

Brand: Addonics Technologies Pages: 9

Brand: Seagate Pages: 42

Brand: I-O DATA Pages: 2

Brand: HOLZMANN MASCHINEN Pages: 18

Brand: PINIE Pages: 8

DKC-F810I-1PL16

Brand: Hitachi Pages: 36

Brand: Cavalry Pages: 20

CADA-U32A Series

Brand: Cavalry Pages: 20

Brand: G-Technology Pages: 15

Brand: G-Technology Pages: 23

G-RAID with Thunderbolt

Brand: G-Technology Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands