GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 134 / 346

Creating a new file system - Basic K2 SAN

Prerequisites for the K2 RAID chassis are as follows:

•

Fibre Channel cable(s) connected

•

Ethernet cable(s) connected

•

Power on

•

Disks bound

Prerequisites for the optional K2 RAID Expansion chassis are as follows:

•

Fibre channel cable(s) connected

•

Power on

•

Disks bound

1. If you have not already done so, launch Storage Utility from the K2Config application.

2. As prompted, wait while Storage Utility gathers system information, then Storage Utility opens.

3. In Storage Utility, click

Tools | Make New File System

The Setting dialog box opens.

4. For the Real Time Input/Output (RTIO) rate, enter the value specified by your system design. If

you do not know this value, contact your Grass Valley representative.

5. Configure Windows Security as follows:

•

If the K2 SAN is on a network Workgroup (not domain), do not select

Windows Security

•

If the K2 SAN is on a network domain, you may select

Windows Security

NOTE: Only select Windows Security if the K2 SAN is on a domain. Never select Windows
Security if the K2 SAN is on a workgroup.

134

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands