GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 194 / 346

•

Disks bound

1. If you have not already done so, launch Storage Utility from the K2Config application.

2. As prompted, wait while Storage Utility gathers system information, then Storage Utility opens.

3. In Storage Utility, click

Tools | Make New File System

The Setting dialog box opens.

4. For a Nearline system, enter zero as the Real Time Input/Output (RTIO) rate.

5. Leave Windows Security unchecked.

6. Click

The Configuration File dialog box opens.

The configuration file for the media file system is displayed.

194

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands