GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 114 / 346

background image

12. On the Recover Data page, click

OK

.

The restore process begins.

13. On the My Recovery Details page, select the

Progress

tab to view the progress.

The image loads in approximately 9 minutes.

14. When the data is successfully restored, click

OK

.

15. Close all Acronis pages and the Acronis main window.

The machine restarts automatically.

16. Remove the recovery media while the machine is shutting down.

17. When prompted, enter the machine name.

Make sure the name is identical to the name it previously had.

After start up, one or more device discovery windows can open. Allow processes to complete
without interference.

At first start up after reimage, the system is in Embedded Security Update mode by default.

Next, do the following to restore the K2 Media Server to its factory-default state. Refer to related
topics in this document or as otherwise indicated.

1. Set up Windows.
2. Restore network configuration.
3. Install the SiteConfig Discovery Agent.
4. Install SNFS software manually. Do not use SiteConfig.
5. Restart.
6. Install K2 software manually. Do not use SiteConfig.

While manually installing software, accept any hardware installation or driver/security prompts
that appear. Also refer to related topics in "K2 Release Notes".

7. Install Fibre Channel Card driver.
8. Activate Windows within 30 days.

Related Topics

Embedded Security modes and policies

on page 116

Setting up Windows

on page 115

Restoring network configuration

on page 282

Installing the Discovery Agent on a K2 Media Server

on page 114

Installing the Fibre Channel card driver

on page 288

Activating the Windows operating system

on page 116

Installing the Discovery Agent on a K2 Media Server

If the device that you plan to manage with SiteConfig does not have a SiteConfig Discovery agent
installed, use this topic to verify and, if necessary, manually install SiteConfig support software.
Doing so allows SiteConfig to discover and manage the device. If the device has any version of the

114

K2 SAN Installation and Service Manual

2014 01 27

Managing K2 Software

«
...
112
113
114
115
116
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

Brand: DB GROUP HERRAJES Pages: 4

Brand: NEC Pages: 59

Brand: Bahco Pages: 4

System Storage TS2900

Brand: IBM Pages: 130

Fiberglass Underground Storage Tanks

Brand: Xerxes Pages: 31

Brand: Hama Pages: 4

220-420LTO - QUICK

Brand: TANDBERG Pages: 8

HTS541680J9SA00 - Travelstar 80 GB Hard Drive

Brand: Hitachi Pages: 167

HTS541616J9AT00 - Travelstar 160 GB Hard Drive

Brand: Hitachi Pages: 2

HTS721010G9AT00

Brand: Hitachi Pages: 2

HTS541616J9AT00 - Travelstar 160 GB Hard Drive

Brand: Hitachi Pages: 188

HTS722010K9A300

Brand: Hitachi Pages: 2

Active Crystals FM01SW80

Brand: Philips Pages: 72

WD Elements WDE1UBK10000

Brand: Western Digital Pages: 2

Brand: ABSCO SHEDS Pages: 25

Brand: Cavalry Pages: 16

Brand: Cavalry Pages: 16

CADT-SA2 Series

Brand: Cavalry Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands