GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 154 / 346

3. In Storage Utility tree view, expand the node for the K2 RAID, right-click the icon for a RAID

controller, and select

Configuration | Network Properties

The Controller Network Settings dialog box opens.

4. In the Controller Slot Number field enter

and then press

Enter

The settings from controller 0 are loaded into the Controller Network Settings dialog box and
are available for you to modify.

5. Enter the control network IP address and other network settings.

6. For SNMP Configuration, enter the IP address of the SNMP manager PC.

You can also enter IP addresses for other SNMP managers to which you want to send SNMP
trap messages.

Refer to related topics about Grass Valley recommended deployment and monitoring solutions
in "K2 Release Notes".

7. For the RAID chassis with two controllers, in the Controller Slot Number field enter

and then

press

Enter

The settings from controller 1 are loaded into the Controller Network Settings dialog box and
are available for you to modify.

8. Repeat the previous steps to configure controller 1.

9. Click

to save settings and close.

10. In Storage Utility click

View | Refresh

154

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands