GRASS VALLEY K2 SAN Installation And Service Manual Download

Page: 90 / 346

8. To modify planned settings, do the following:

a) Select the network settings and click

Edit

The Edit IP Address dialog box opens.

b) Edit IP address settings as follows:

For network interface Control Team

Setting...

Control

is required

Network

Static

is recommended.

Address Allocation

The IP address for this interface on the network. Required.

IP Address

For basic SAN network interface Media Connection #1

Setting...

iSCSI (non-Redundant)

is required

Network

Static

is required.

Address Allocation

The IP address for this interface on the network. Required.

IP Address

For redundant SAN network interface Media Connection #1

Setting...

iSCSI (Primary Redundant)

is required

Network

Static

is required.

Address Allocation

The IP address for this interface on the network. Required.

IP Address

For redundant SAN network interface Media Connection #2

Setting...

iSCSI (Secondary Redundant)

is required

Network

Static

is required.

Address Allocation

The IP address for this interface on the network. Required.

IP Address

K2 SAN Installation and Service Manual

2014 01 27

Planning and implementing a K2 SAN with SiteConfig

Summary of Contents for K2 SAN



























































































































































































































































































































































Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands

GRASS VALLEY K2 SAN, Installation And Service Manual

Search results

Summary of Contents for K2 SAN

Reviews:

Related manuals for K2 SAN

Brands by name

Popular brands