GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 205 / 346

background image

Configure Network Configuration page - NH server

This page displays the control network Ethernet port, and allows you to configure the FTP/Streaming
network Ethernet port.

1. Verify that the top port is configured correctly.

The top port is the port over which the K2Config application is communicating. If correctly
configured, it is already assigned the control network IP address, as displayed on this page.

2. Verify that the FTP/Streaming port is configured correctly. If not configured correctly, do the

following:

a) Select the other port and click

Modify

.

A network configuration dialog box opens.

b) Enter the FTP/Streaming IP address and the subnet mask and click

Apply

.

3. Click

Next

.

The File System Server Configuration page opens.

2014 01 27

K2 SAN Installation and Service Manual

205

Configuring and licensing the K2 SAN

«
...
203
204
205
206
207
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

G-DRIVE mobile USB

Brand: G-Technology Pages: 18

Brand: G-Technology Pages: 34

Brand: JCAT Pages: 3

BARRACUDA 7200.10 ST3160215AS

Brand: Seagate Pages: 2

Brand: Geekworm Pages: 13

Brand: Western Digital Pages: 3

Brand: Whalen Pages: 15

Brand: Seagate Pages: 86

Brand: eSafe Pages: 12

Brand: Supermicro Pages: 81

Brand: Grizzly Pages: 2

Brand: Grizzly Pages: 6

Brand: Grizzly Pages: 32

Brand: red lion Pages: 8

FileCruiser VA2600

Brand: Promise Technology Pages: 203

Brand: Promise Technology Pages: 232

Brand: ABSCO SHEDS Pages: 30

Brand: EverFocus Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands