GRASS VALLEY K2 SAN Installation And Service Manual Download | Manualshive

Page: 166 / 346

background image

Configuring server B

Prerequisites:

•

Server A is configured

•

The restart of server A after it is configured is complete

After you have configured the first K2 Media Server (server A) you next configure the redundant
K2 Media Serer (server B).

1. Verify that server A has restarted by opening the MS-DOS command prompt and use the “ping”

command.

2. In the K2 System Configuration application tree view, select the K2 Media Server you are

configuring as server B.

3. Click the

Configure

button.

The Configure K2 Server wizard opens to the Define server roles page.

Configure Define Server Roles page - Redundant K2 SAN server A and server B

1. Enter the name for the K2 Media Server, as currently configured on the machine.

2. Enter the name or IP address of the Ethernet switch, as currently configured on the switch, to

which the K2 Media Server is connected.

3. Select all roles, except as follows:

If the K2 SAN has one or more optional NH servers, then FTP traffic should go to the NH server,
not the K2 Media Server you are now configuring. In this case, do not select the FTP server role
or the NAS server role

4. Click

Next

.

166

K2 SAN Installation and Service Manual

2014 01 27

Configuring and licensing the K2 SAN

«
...
164
165
166
167
168
...
»

Summary of Contents for K2 SAN



























































































































































































































































































































































Reviews:

No comments

Related manuals for K2 SAN

DS8000 - ADDITIONAL INFORMATION

Brand: IBM Pages: 5

System Storage TS7600 ProtecTIER Series

Brand: IBM Pages: 132

Brand: IBM Pages: 188

Brand: Overland Storage Pages: 6

Brand: U-Line Pages: 3

Cheetah 15K.7 FC

Brand: Seagate Pages: 90

StorageTek SL8500

Brand: Oracle Pages: 59

Brand: Wayfair Pages: 22

Brand: Cavalry Pages: 16

Brand: Cavalry Pages: 16

CADA-C32A Series

Brand: Cavalry Pages: 18

MediaShare Wireless SD/USB device

Brand: Verbatim Pages: 21

Brand: Verbatim Pages: 40

Brand: TerraMaster Pages: 13

TIGERFLEX SHIPLAP APEX BIKE SHED

Brand: Tiger Pages: 16

Brand: HP Pages: 1

Brand: HP Pages: 1

Brand: HP Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands