manualshive.com logo in svg

Emerson Rosemount 5900S Series, Reference Manual

Share
Download
Emerson Rosemount 5900S Series Reference Manual Download Page 51

2. Tighten the nut so that the Flange Ball fits tightly to the flange (torque 50 Nm).

Mounting the welded Flange Ball

Follow this instruction when installing the welded Flange Ball on a flange.

Prerequisites

For horizontal mounting according to requirements in chapter 

Parabolic antenna

requirements

, make sure that the diameter of the hole is 116 ± 2 mm.

Figure 3-18: Flange Requirements

$

%

A. 116±2 mm

B. 6-38 mm

In case the flange requirements in chapter 

Parabolic antenna requirements

 are not met,

the hole needs to be machined to an oval shape prepared for inclined welding of the
Flange Ball.

Reference Manual

Installation

00809-0100-5900

September 2019

Rosemount 5900S Radar Level Gauge

51

Summary of Contents for Rosemount 5900S Series











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands